• 𝕸𝖔𝖘𝖘@infosec.pub
    link
    fedilink
    English
    arrow-up
    3
    arrow-down
    1
    ·
    6 months ago

    Hahaha!! I wish! Actually, I have old equipment that only takes the 6.35mm TS (and a couple TRS) connectors, and I don’t like adaptors, as they almost always noticeably reduce audio quality.

    • WaterWaiver@aussie.zone
      link
      fedilink
      English
      arrow-up
      3
      ·
      6 months ago

      I don’t like adaptors, as they almost always noticeably reduce audio quality.

      Huh? 3.5mm to 6.35mm adapters, the small bits of metal and plastic, or are you talking about something else?

      • 𝕸𝖔𝖘𝖘@infosec.pub
        link
        fedilink
        English
        arrow-up
        1
        arrow-down
        1
        ·
        6 months ago

        Yeah. Maybe I just bought the super cheap ones? Not sure. I ended up getting a 3.5 to 6.35 cable, and haven’t had a problem since.

        • WaterWaiver@aussie.zone
          link
          fedilink
          English
          arrow-up
          2
          ·
          6 months ago

          That’s really weird o.o The adapters should just be metal and plastic, same as the cables.

          Maybe they have a really weak connection internally, ie high resistance? This might lead to both lower volume in the headphones and (in some circumstances) higher noise, especially if it’s an unstable resistor.

          I recommend starting a shelf of cursed items :)

            • WaterWaiver@aussie.zone
              link
              fedilink
              English
              arrow-up
              2
              ·
              edit-2
              6 months ago

              This could end up competitive.

              Invite people to your house, give them a tour and briefly mention the shelf before scurrying them on. Watch their faces contort but don’t give them the opportunity to ask any questions.

              EDIT: I have a vague guess at what could have gone wrong with your adaptor. It might have had OK L and R contacts but a broken G contact. You would then hear the difference between the L and R channels, which most often sounds like garbage. Music would be weird (entire instruments/vocals disappear) and mono audio would be silent or near-silent (so you’ll have to turn it up a lot and will hear noise).

              • 𝕸𝖔𝖘𝖘@infosec.pub
                link
                fedilink
                English
                arrow-up
                2
                ·
                6 months ago

                Hahaha!! Like a random red door on the back wall of the basement. “That’s just ‘the door’. Nothing to worry about, as long as you keep your distance” and quickly walk them off with no further explanation. Hahahahaha

                That makes sense. I used to get the adapters from a local shop where I used to live, and they were cheap cheap. Converted to USD, they were probably around $0.10 a piece. He gave them out free when you purchased headphone. After a while I got tired of the static and low sound quality, so I just got a cable (3.5-6.35) on ebay, and it’s been fine since.

          • barsoap@lemm.ee
            link
            fedilink
            arrow-up
            1
            ·
            edit-2
            6 months ago

            The quality of random no-brand audio cables, connectors, adapters etc. tends to be right-out atrocious. There’s technically going to be metal in there but that “nice”, thick headphone cable that came with those cheap headphones (and even some decent ones, like AKG K240s) is going to consist mostly of insulation, not conductors. Plastic is quite a bit cheaper than copper.

            You can get ok jack adapters for 80ct but honestly I wouldn’t trust that thing if I didn’t trust Thomann. Usually I’d be looking for Rean when wanting a cheap one but they’re apparently not in stock. And I kinda doubt Neutrik or Hicon even produce them if you’re spending five bucks on a 3.5mm jack you’re not using adapters, you’re soldering the exact cable you need.

            Oh. Back to resistance: Doesn’t really matter audio quality doesn’t care it’s still the same AC signal just with less amplitude which you can fix with the volume knob, You’re looking for impedance and material boundaries have a habit of being bad for it, as well as signal quality as parts of the signal will propagate through the boundary and parts will reflect. For more information ask an actual electrical engineer I merely wrote an A in a course I had to take and can tell the hot end of a soldering iron from the cold one (it’s the one with the cable).

            • WaterWaiver@aussie.zone
              link
              fedilink
              English
              arrow-up
              2
              ·
              edit-2
              6 months ago

              Oh. Back to resistance: Doesn’t really matter audio quality doesn’t care it’s still the same AC signal just with less amplitude

              Only for ideal resistors.

              Resistors are noise sources. Intentional resistors tend not to be too bad (and probably won’t be heard in this situation unless you have super-high-impedance headphones, perhaps 10’s of K), but unintentional resistors (eg corroded unstable metal contacts inside a plastic part) can be atrocious.

              A few things to add to this:

              (1) If your resistor acts even slightly like a diode then you will encounter partially rectified RF signals (more noise yay). Metal oxides between metals can do this, eg if the connector has crimped two badly-plated bits of metal together.

              (2) Plasticisers in some plastics can leak out, causing corrosion on unseen internal metal parts.

              (Of course linking all of this together is just conjecture, the causes of Moss’ bad adaptors might be something completely different)